LIBRARY FURNITURE
CONDITIONS OF THE CONTRACT AND DIVISION 1, as indexed, apply to this Section.
A.Refer toSection AB for substitutions.
1.2SUBMITTALS
A.Shop Drawing
B.Drawing:Indicate size, material and finish.
A.Tesco Industries, Inc. 1-800-353-3685
2.2MATERIALS
A.Catalog Standards:Model numbers listed are by Tesco Industries, Inc.
Catalog description for indicated number constitutes requirements, unless otherwise specified.
B.Wood Species:
01All wood used in the construction of furniture and cabinets shall be northern grown red oak and shall be selected form seasoned, kiln-dried materials free from structural imperfections.The moisture content at time of fabrication shall range from 5% to 7%.All woods shall be selected for uniformity of grain and color.Wood used for internal parts shall be selected a structurally sound.
02All plywood used shall be of quality as specified by the American Plywood Association.All facing materials shall be no less than 1/28” thickness after sanding.Face veneers (i.e. veneers facing an exterior surface) shall be select, plain sliced, slip matched, to selected species.
C.Plastic Laminates:
01All high pressure plastic laminate shall meet ANSI/NEMA
LD3-1991 specifications.Horizontal top surfaces are laminated with .050” thick laminate and a .030” thick phenolic backer sheet is applied on the reverse side of all horizontal surfaces.Vertical surfaces are laminated with a .030” thick laminate on each side.
D.Wood Finishes:
01In
the manufacturing process after parts are cut and ready to finish, all
solid oak panels and shelves are dipped in Nelsonite 15B02 wood stabilizer.Prior
to assembly, parts pass through a 5 head wide belt sander which has 100,
120, 150, 180, and 220 grit sand paper.Parts
are then inspected, filled and hand sanded as necessary until thoroughly
cleaned.
After
sanding, the parts are roll coated with 100 percent solid U.V. stain, wiped,
U.V. oven cured and then pass through a deburring station.
Then
parts are roll coated with a 100 percent solid U.V. sealer, U.V. oven cured,
then passed through a final deburring station.
Next
parts are roll coated with a final 100 percent U.V. clear top coat and
then U.V. oven cured.
All
sealers and finishes must be U.V. and applied by a flat line roll coat
system to insure a uniform and environmentally safe finish.
2.3CONSTRUCTION
A.Table:
01Table tops shall be 1-1/4” thick consisting of a 1-13/16” 7-ply hardwood lumberwith plastic laminate and backer sheet.Center ply of the lumber core shall consist ½” thick edge-glued hardwood lumber strips of random widths with two outer cross banded veneers of 3/32” hardwood.To either side of this, a layer of 1/8” long grain hardwood and a layer of 1/8” short grain hardwood are added.The 1-3/16” core then receives a layer of .050” high pressure plastic laminate and a layer of .030” phenolic backer.Table tops with internal edge bands have the edge bands applied before the application of plastic and backer.Tops shall have standard edge banded with 3/4” x 1-1/4” external bullnose solid oak edge bands which are applied after the application of backer and laminate, unless otherwise specified in the equipment schedule.
Legs shall be constructed of two pieces of two pieces of solid oak, glued and machined to a minimum of 2-3/8” square.Legs shall be attached to the top by means of a 5” x 5” x 5/16” metal-flanged plate.The mounting plate to be attached to the legs by means of 5/16” x ¾” machine bolts into 5/8” barrel nuts inserted into the leg.The plate will in turn attach to the table top by means of 5/16” x 1” machine bolts into metal inserts in the table top.Legs shall be equipped with a 1-3/4” diameter adjustable glide screwed into an
insert and used for leveling and height adjustment.Tables shall have an apron trim of 1-1/8” x 2-1/8” solid oak and shall fit between the legs to form a reveal design.The apron shall be attached to the table from the underside with 1-1/4” x #10 wood screws.A 14 gauge “V” shaped metal keel shall be attached to the underside on all tables 60” and longer.
B.Shelving:
01All
vertical uprights of library shelving shall be a minimum of 1” thick,
kiln
dried
solid oak, glued up in strips no less than 1-1/2" and no more than 4",
andfree of all imperfections.Veneered
plywood of any type and / or uprights of less than 1” thickness will not
be acceptable.
The
2" canopy cornice shall be constructed of an oak plywood top with solid
oak facia strips which are machine applied to front and back edges.Bolting
cleats are attached by means of wood screws and glued construction.
Continuous
top shelving shall have a 2" deep dovetailed top frame provided with countersunk
holes for screwing down a continuous top made of solid core with standard
(Statesman) internal straight solid oakedge
bands or as specified in the equipment list.Bases
shall be of solid hardwood 3-1/2" in height with dovetail joints.
Shelving
units shall be standard with back panels on single faced shelving and divider
panels on double faced units.Backs
shall be 1/4" thick oak plywood and finished on one side for single faced
units and both sides for double faced units.Backs
shall be recessed in a dado on all sides.End
panels shall be joined to cornice and base by means of metal ferrules embedded
in the end panels with 5/16" hex head bolts passing through the cleats
on the cornice and the sides of the base and engaging the ferrules.Filler
and corner units shall be supplied as needed to complete shelving runs
as shown on the plan.
Shelves
shall be a minimum of 3/4" thick, edge glued, solid oak strips
no less than 1-1/2" wide nor more than 4" wide.The
underside of all shelves shall be neatly routed to receive the metal supporting
pins. Adjustment of shelves shall be of pin hole style construction with
adjustments at 1-1/4" increments, which provides for a cleaner less conspicuous
installation.
Adder
shelving units shall be joined by means of 5/16" hex head bolts passing
through both bases and the intermediate upright,both
cleats on the cornices and the intermediate upright, and then secured with
washers and nuts.
All
shelving 60" high and under can have a continuous style top with high pressure
plastic laminate surface.Continuous
tops when used, shall have the standard edge banded with 3/4” x 1-1/4”
external bullnose solid oak edge bands which are applied after the
application of backer and laminate.All
shelving 72” and higher will have a 2” wood veneer canopy top to match
shelving unit..
Shelf
arrangements per face shall be as follows:
HeightBaseAdjustableTotal
36"112
42"123
48"12
(3 available)3 (or 4)
60"145
72"156
84"167
96"178
Units
may be orderedwith sloped magazine
shelves, picture book shelves, or newspaper inserts.The
Number of adjustable shelves will vary when optional shelf styles are ordered.
C.Seating:
01CHAIRS
- MANUFACTURED BY OTHERS- FINISHED TOMATCH
LIBRARY FURNITURE:
Library Chairs:Chairs to be of oak wood construction stained to match library furniture.All Joints are to be multiple doweled and frames shall be reinforced with heavy wood corner blocks, glued and screwed in place.Back posts, front posts, side rails and sled rails shall be made of 5/4" oak finished to 1-1/16" thickness and 2" width.Front rails, back rails andcross stretchers shall be 4/4" oak finished to 13/16" thickness and 1-1/2" width.Side assembly shall be flush sanded on both sides and all edges shall be eased.Both top corners of the back posts and the top front corner of the front posts shall be shaped to a 3/8" radius. The side posts shall be shaped to the contour of the back posts and the top and bottom rails shall be steam bent to a 24" radius.
Seat and back shall be made of an assembled rail construction with each joint containing two 3/8" x 2" spiral groove dowels and shall be removable.Seat and back can be upholstered.
Frame shall be of leg or sled base type of 5/4" solid oak finished to 1-1/16" thickness x 2-1/4" width and shall be double doweled to the bottom of the front and back posts using 3/8" x 2" spiral groove dowels.
Librarian's
Chair:Construction and upholstery
to be the same as Library Chairs.Base
shall be solid oak with carpet casters and shall be adjustable.
Charging Desk Stool:Construction and upholstery to be the same as Library Chairs.Base shall be solid oak with carpet casters and shall be adjustable.
Reading Area Furniture:Reading area lounge furniture shall be of oak wood construction stained to match library furniture.back posts, front posts, arms and sled rails shall be of 8/4” solid oak finished to 1-3/4” thick x 3” wide.Side rails shall be of 8/4” solid oak finished to 1-3/4” thick x 4-1/8” wide.Back seat rail shall be of 5/4” solid oak finished to 1” thick x 4” wide and be triple doweled to the side rails using 7/16” x 2” spiral groove dowels.Arms, side rails, and sled rails shall be triple doweled to the front and back posts using 7/16” x 2” spiral groove dowels.Seat support (2 required) shall be of 4/4” solid oak finished to 7/8” thick x 2-1/4” wide and shall be double doweled to the front and back rails using 7/16” x 2” dowels.Back support rail shall be of 5/4 solid oak finished to 1-1/16”thick x 3-1/8”wide.The front shall be beveled to accept the back.The rail shall be triple doweled between the arms using 7/16” x 2”spiral groove dowels.An additional 1” x 1-1/4” widerail shall be attached to the underside of the rail by glue ad nine 12 x 1-3/4” tapping screws to increase support.Side assembly shall be flush sanded on both sides and each joint.The top of the arm shall be shaped to a 7” radius.All four corners shall be shaped to a 1” radius.Front and back corner blocks shall further reinforce the frame and shall be glued and screwed into place using polyvinyl alcohol ester blend with polyvinyl acetate glue, four 10 x 1-1/4” twinfast screws, and two 7 x 70mm confirmat screws.
Upholstered back shall be made of an assembled rail construction with each joint containing two 7/16” x 2” spiral groove dowels.The seat shall be equipped with a flex-o-later unit, seven helicals, an insulator and 5” thick minimum 1.8 PCF density polyurethane cushion wrapped with 3/4” Dacron.Upholstery shall be pre-sewn-sewn and triple stitched.Grade 100 is standard.
D. Circulation Desks
CIRCULATION
DESK AND COMPONENTS - 4400 Series:
Circulation
Desks shall be designed using a modular concept with a continuous top.Modules
shall be available in 32", 36", 39", or 42" high units as specified on
equipment list.Each module shall
be 36" wide x 26 3/4" deep with a 30" deep continuous top.A
pair of finished end panels are required at the end of each circulation
desk configuration.
Facing
materials shall be 3/4" thick,7-plyplywood
with oak veneer facing and solid oak edges.Themodules
shall be as shown in the design specifications.All
components shall be manufactured using oak plywood with matching solid
oak framing.All exterior materials
used shall be 3/4" thick, 7-ply oak plywood with face veneers 1/28" thick,
matched for color and grain uniformity and with a solid oak edge.
The
top shall be of a continuous designfabricated
in as large of sections as possible and shall be joined together by a draw
bolt method.The top shall be 1-1/4"
thick with a surface of .050" thick high pressure plastic laminate over
a lumber core with .030" thick phenolic backer sheet on the underside.Tops
shall have standard (Celebrity) 3/4” x 1-1/4" external bullnose solid oak
edge bands which are applied before the application of backer and laminate,
or as specified in the equipment schedule.
Drawer
fronts shall be made of 3/4" thick solid red oak lumber, edge glued forming
a continuous solid wood drawer front.Drawer
sides and parts shall be 1/2" thick solid oak with dovetail joints and
a 1/4" bottom recessed on all four sides.Drawer
fronts shall be removable.Drawers
shall be equipped with side-mounted, full-extension drawer slides as manufactured
by Accuride C3832-A 100# capacity.Drawer
pulls shall be wire pulls furnished in a brass matt finish.
Doors,
end panels, and shelves shall be 3/4” thick 7-ply plywood with an oak face
veneer of 1/28” thick, matched for color and grain with a solid oak edge
to match.Doors shall be hung with
two commercial grade, European, concealed, self closing hinges (91A6600)
and shall be flush insert style.Shelves
shall adjust by means of pin holes.KV
strips shall not be acceptable.
All
framing materials shall be of kiln dried oak selected for structural soundness
and shall be a minimum of 3/4" thick.
Finished
End Panel:Finished
end panels are required at each end unit of a circulation desk and shall
be of 3/4” thick oak plywood with solid oak edge banding.
4445
- Depressible Book Truck:The
depressible book truck shall be constructed of 3/4" thick oak plywood sides
and bottom with matching oak edge banding.The
truck shall be provided with four 3" diameter swivel casters.Unit
shall have a floating shelf surface which shall be covered in a neutral
colored high pressure plastic laminate and shall be supported by a spring
action depressing mechanism that lowers with the weight of the books.Rubber
bumpers may be ordered as an option.
Circulation
Desk – 6400 Series
Modular
components shall be of the design and description outlined in the equipment
schedule.Components have individual
captured tops to allow ease of rearrangement if so desired with minimal
effort.
All
components shall be constructed of ¾” thick, 7=ply veneer core hardwood
plywood with oak veneer facing 1/28” thick and solid oak edge bands.Individual
tops shall be lumber core surfaced with .050” thick high pressure laminate
with a .030” thick backing sheet on the underside.All
exposed edges of the top shall be banded with the solid oak edge style
specified for the project.The tops
shall be captured within 29” deep end panels.Each
cabinet shall be separated by a ¼” reveal strip.A
pair of finished end panels shall complete the entire assembly.
All
interior framing material used in the construction of the units shall be
of kiln-dried hardwood selected for structural soundness and shall be a
minimum of ¾” thick.
Drawer
fronts on all units will made of ¾” thick northern solid oak edge
glued to form a continuous solid wood drawer front for lasting strength
and durability.Drawer sides and
parts will be ½” solid hardwood with dovetail joints and ¼”
bottom recessed on all four sides.Drawers
shall be equipped with side mounted, full extension drawer slides.Drawer
pulls are provided in bronze or aluminum finish.
All
doors and end panels shall be of ¾” thick seven-ply oak plywood
with oak veneer facing 1/28” thick and banded all exposed edges with solid
oak.Doors will be hung with two
commercial grade, concealed, self-closing hinges.
Units
with shelves will be drilled with pin holes to provide support for the
shelves.
All
exterior fronts are made of ¾” thick, seven-ply oak plywood with
rift cut face veneers 1/28” thick matched for color and grade uniformity.Individual
tops shall be lumber core surfaced with .050” thick high pressure laminate
with a .030” thick backing sheet on the underside.All
exposed edges of the top shall be banded with the solid oak edge style
specified for the project.The tops
shall be captured within 29” deep 1” thick finished end panels.
All
interior framing material used in the construction of the units shall be
of kiln-dried hardwood selected for structural soundness and shall be a
minimum of ¾” thick.
Drawer
fronts on all units will made of ¾” thick northern solid oakstrength
and durability.Drawer sides and
parts will be ½” solid hardwood with dovetail joints and ¼”
bottom recessed on all four sides.Drawers
shall be equipped with side mounted, full extension drawer slides.Drawer
pulls are provided in bronze or aluminum finish.
All
doors and end panels shall be of ¾” thick seven-ply oak plywood
with oak veneer facing 1/28” thick and banded all exposed edges with solid
oak.Doors will be hung with two
commercial grade, concealed, self-closing hinges.
Units
with shelves will be drilled with pin holes to provide support for the
shelves.
E.Technical
Furniture
Atlas
Stand:Legs
and apron construction to be the same as Tables.Cabinet
ends and front shall be 3/4" 7-ply oak veneer plywood with solid oak edge
bands.Case shall house shelves constructed
of3/4" oak plywood with solid oak
retainer strip on front edge.Shelves
to slide on full extension slides.Top
shall be 1-1/4" thick constructed of 1-1/8" solid core, .050" plastic laminate,
.030" phenolic backer, and solid oak edge bands.Edge
bands shall be the same as on the tables for the project. Legs are attached
with 4 - 14 ga. steel vertical corner leg brackets.The
leg base unit is permanently attached to the atlas cabinet body.The
apron rail which is mounted between the legs shall be constructed of 3/4"
x 3-1/2" solid oak and attached to the top with countersunk screws.
Dictionary
Stand:Legs
and apron construction to be the same as Tables.Cabinets
ends and front shall be 3/4" 7-ply oak veneer plywood with solid oak edge
bands.Case shall house one adjustable
shelf constructed of3/4" oak plywood.
Top shall be 1-1/4" thick constructed of 1-1/8" solid core, .050" plastic
laminate, .030" phenolic backer, and solid oak edge bands.Edge
bands shall be the same as on the tables for the project.Legs
are attached with 4 - 14 ga. steel vertical corner leg brackets.The
leg base unit is permanently attached to the body of the unit.The
apron rail which is mounted between the legsshall
be constructed of 3/4" x 3-1/2" solid oak and attached to the top with
countersunk screws.
Book
Cart and Easel:Cabinet
constructed of 3/4” oak plywood with solid oak edge bands with a 1-1/4”
HPL top with solid oak full rounded bullnose edgeband.4
- 3” casters.Shelves are removable
and can be positioned horizontally and vertically.
Secretarial
and/or Executive Desk:Desk
end panels shall be constructed with 1” 9-ply oak veneer plywood with solid
oak edge bands.Modesty (front panel)
shall be constructed of 3/4” 7 ply oak veneer plywood with solid oak edge
bands.Framing materials shall be
3/4” solid hardwood.Desks may have
various arrangements of drawer pedestals, lap drawers and returns as noted
by the equipment schedule.
Top
shall be 1-1/4” thick consisting of 1-1/8” lumber core, .050” plastic laminate,
.030” phenolic
backer,
and 3/4” solid oak edge bands.Edge
bands shall be 3/4” x 1-1/4” internal solid oak edge bands which are applied
before the application of backer and laminate, unless otherwise specified
on the equipment schedule.
Drawer
fronts shall be made of 3/4” thick northern oak, edge glued forming a continuous
solid wood drawer front which is applied to a completed drawer box and
is removable.Drawer sides and parts
shall be 1/2” thick solid oak with dovetail joints and a 1/4” bottom recessed
on all four sides.Drawers shall
be equipped with side mounted full extension Accuride C3832 drawer slides.Drawer
pulls shall be in a bronze finish Amerock BP 30535-AE.
Portable
Book Truck:End
panels bottom, and shelves are constructed of 3/4” solid oak.Shelves
re glued, screwed and tenoned into the end panels.Portable
book trucks may be ordered in single face or double face units with flat
shelves or sloped shelves.Bottom
shelf will be flat. Units shall be equipped with 5” casters, 2 swivel ,
2 fixed.
Card
Catalog:Sides
of the drawer cabinet shall be 3/4” thick, 7-ply oak plywood with solid
oak edge bands.Framing shall be
solid oak.
The
unit is supported with four vertical 2-3/8” solid red oak legs which are
a permanent portion of the unit base frame and are attached with 14 gauge
steel vertical corner leg brace (EA7) in construction with its perimeter
style apron rail design.Each leg
is attached by means of two 5/16” x 18” x 3”long
hanger bolts per leg for frame corner rigidity.Top
of unit shall be 1-1/4” thick and constructed from solid core with .050”
high pressure laminate top surface and .030z’ phenolic backer.Edge
bands on top shall match those of tables used on the project.
Drawer fronts shall be 3/4” thick solid oak and finished to match.Drawer fronts shall have two compartment bronze finish pulls fastened to the drawer with concealed screws.Card trays are 5-5/8”w x 16”d x 2”h and are constructed of beige colored high density ABS plastic.Each tray shall be equipped with and adjustable, positive locking metal follower operating in a plastic channel.A round metal rod shall be in each tray to secure the cards in the tray.Rods shall have a metal knob and shall engage in a concealed spring loaded latch to permit the removal or replacement of the cards.Drawers shall slide on solid hardwood slides.
Magazine
Rack:Legs
and apron construction to be the same as tables.Cabinet
sides and back to be 3/4” 7-ply oak veneer plywood with solid oak edge
bands.The cabinet has five vertical
staggered pockets which are constructed of 1/2” solid oak hardwood and
has a rear storage bin at the base of the vertical pockets.The
unit is supported with four legs and apron frame attached to the cabinet
by means of EA6 metal corner brackets and 5/16” lag screws into the legs.Standard
width is 36”
Paperback
Display:Oak
frames with rotating towers.Each
5 tier tower holds approximately 150 paperback books.Frames
are constructed of 1-3/4” thick square solid oak members 62”H x 25”W with
an oak cross member 12” from the bottom to give a clearance of 49” for
the placement of the molded plastic display tower which rotates on a steel
rod.Each frame has 2 adjustable
glides for leveling.Towers are available
in 5 tier or tier.
Basic
unit consists of 2 frames - 2 towers.Additional
frames and towers can be added to formsquare
design (4 towers - quad) or any number of zig-zag designs.
Podium:Full
panel design constructed of 3/4” 7-ply oak veneer plywood with solid oak
edge bands.Standard size is 27”W
x 4”H x 21” D.Sloped top 1-1/4”
thick is recessed 4” between panels for privacy, has plastic laminate surface
and solid oak paper stop.Rear of
top is flat to provide drink ledge.there
are three oak banded plywood shelves - a fixed shelf mounted by oak cleats
below the top, a enter adjustable shelf, and a bottom fixed shelf also
mounted by oak cleats.Mobile units
have 2 - 3” fixed casters and 2 - 3” swivel casters with brakes mounted
to the bottom fixed shelf.
F.CARRELS,
COMPUTER STATIONS, PUBLIC ACCESS STATIONS:
Table
Style Carrels -- Computer/Printer
Tables:Top, legs, and apron shall
be the same construction as tables.Rack
shall be constructed of 3/4” 7-ply oak veneer plywood with solid oak edge
bands.Rack end panels, divider
panels, and back shall be joined with dado joints.Rack
shall be securely mounted from the underside of the table.Accessories
will be supplied only as ordered.
Panel
Post Carrels:Carrels
are available as either double face or single face units and in starter/adder
configurations.Standard single face
size is 36”w x 48”h x 30”d, double face size is 36”w x 48”h x 48”d.Other
sizes are available upon request or as noted on bid sheets.
The
carrel work surface shall be a nominal thickness of 1-1/4” consisting of
lumber core with top and bottom hardwood veneer cross banding, .050” high
pressure plastic laminate top surface and .030” phenolic backer.Tops
shall be edge banded with 3/4” x 1-1/4” external bullnose solid oak edge
bands which are applied after the application of backer and laminate.
The
work surface is attached to side and back panels with 6” x 1-1/4” x 1-1/4”
metal brackets which are screwed into the underside of the top surface
and bolted into the end panels.Brackets
are attached to the back and side panels with metal bolts threaded into
metal inserts embedded in the plywood panels.Brackets
are then screwed into the underside of the top.
Units
ordered with an adjustable work surface shall have threaded metal inserts
pre-installed in the back and end panels.Work
surface may be unbolted and rebolted at different heights by using these
inserts.
Side
and back panels are constructed of 3/4” 7-ply veneer core plain slice oak
plywood with solid oak edge bands.Side
panels are attached to the posts with concealed metal to metal fasteners.Posts
shall be constructed of two pieces of solid red oak glued and machined
to 1-3/4” square with vertical edges eased and smoothed.Each
post shall receive a chrome plated, 1-1/2” diameter adjustable glide screwed
into an insert and used for height adjustment.
Reference
and paper shelves, if ordered, shall be 10” deep and constructed of 3/4”
7-ply oak veneer plywood with a 2” solid oak facia.The
reference shelf is located 2-1/4” below top of back panel.The
paper shelf is placed 12” below the work surface.Reference
and paper shelves are attached with 4 - 6” x 1-1/4” x 1-1/4” metal brackets
which are bolted with metal to metal fasteners to side and back panels
and screwed to the underside of the shelf.
Full
Panel Computer Carrels:Carrels
are available as either double face or single face units and in starter/adder
configurations.Standard single face
size is 36”w x 48”h x 30”d, double face size is 36’w x 48’h x 48”d.Other
sizes are available upon request or as noted on bid sheets.
The
carrel work surface shall be a nominal thickness of 1-1/4” consisting of
lumber core with top and bottom hardwood veneer cross banding, .050”Tops
shall be edge banded with 3/4” x 1-1/4” external bullnose solid oak
edge bands which are applied after the application of backer and laminate.The
work surface is attached to side and back panels with 6” x 1-1/4” x 1-1/4”
metal brackets which are screwed into the underside of the top surface
and bolted into the end panels.Brackets
are attached to the back and side panels with metal bolts threaded into
metal inserts embedded in the plywoodpanels.Brackets
are then screwed into the underside of the top.
Units
ordered with an adjustable work surface shall have threaded metal inserts
pre-installed in the back and end panels.Work
surface may be unbolted and re-bolted at different heights by using these
inserts.
Side
and back panels are constructed of 3/4” 7-ply veneer core oak plywood with
solid oak edge bands.Side panels
are attached to the back panel with concealed metal to metal fasteners.The
bottom of the side panels shall be equipped with 1” adjustable glides.
Reference
and paper shelves, if ordered, shall be 10” deep and constructed of 3/4”
7-ply oak veneer plywood with a 2” solid oak facia.The
reference shelf is located 2-1/4” below top of back panel.The
paper shelf is placed 12” below the work surface.Reference
and paper shelves are attached with 4 6” x 1-1/4” x 1-1/4” metal brackets
which are bolted with metal to metal fasteners to side and back panels
and screwed to the underside of the shelf.Depth
of reference and paper shelf may vary according to description on equipment
list.
A.Install equipment under factory supervision.Provide all bolts, blocking,
miscellaneous items necessary for a complete installation.
B.Installation shall be plumb and level, properly aligned between sections and
neatly
finished at walls and doors.
C.After
completion leave installation clean and adjusted.Remove
all debris.